Superheat and Subcooling Calculator with Refrigerant PT Chart
Calculate superheat and subcooling with dew/bubble PT curves, altitude correction, fixed-orifice targets, and TXV/EEV nameplate checks.
Heat load, heat-pump sizing and running cost, wall U-values and condensation, stairs: building calcs that explain their assumptions. Estimates only; they do not replace a certified calculation.
Calculate superheat and subcooling with dew/bubble PT curves, altitude correction, fixed-orifice targets, and TXV/EEV nameplate checks.
Model a year of heat conduction through an under-slab sand battery. Compare stored PV heat, ground and edge losses, January floor temperature, insulation and sand depth.
Compare daily pool heating cost, evaporation and water temperature with and without a cover. Model hourly weather, heat pump performance and a chosen heating run time.
Find economic and capacity balance temperatures, then compare winter cost and COâ‚‚ for a heat pump with resistance backup, dual fuel, and a furnace using editable local weather bins.
Compare R290 charge limits by floor area and installation height. Explore a hole leak, floor accumulation, air changes and detector response, with R32 sizing alongside.
Will a towel warmer moved to another wall still heat by gravity from the hot-water riser? Flow, temperatures and heat output for your pipes, bends and heights, with the stall and backward-flow cases.
Flow and temperature of every section of a sectional radiator connected on one side, diagonally, or through a flow extender tube (pseudo-diagonal), and the hole size that makes a perforated extender heat evenly.
Estimate room cooling load and AC size at 40–50 °C, including roof exposure, solar gain, humidity and high-ambient capacity loss. Compare running-cost scenarios by set temperature.
Estimate window airing time from COâ‚‚ and moisture balances. Compare cold-surface humidity, sensible heat loss and mechanical heat recovery, with animated room-air curves.
Size instant hot-water capacity from flow and winter inlet temperature. Compare electric current, cable voltage drop, breaker inputs, Japanese go ratings and shower cost.
Size a hot water cylinder from mixed-water demand, estimate heat-up time and standby loss, and compare heat-pump electricity, timer capacity and payback.
Estimate heat pump noise at a neighbour's window from sound power, placement, distance and barriers. Includes dated German night and England MCS presets.
Calculate radiator design flows, Darcy pipe losses, required valve kv and pump head for up to six parallel circuits. Compare entered kv values and watch the flow split.
Estimate water underfloor heating output from pipe spacing, screed, covering and water temperatures. Check surface limits, pipe lengths, loop flow and pressure drop.
Check radiator output at heat-pump temperatures, find each room’s minimum flow, size replacements and explore a heating curve and cost-per-degree scenario.
Compare heat-pump hydraulic layouts, mixing and plate-exchanger temperature penalties, COP and seasonal cost. Size active water volume for minimum run time and defrost.
Compare always-on heating, night setback and cheap-hours preheat. See daily kWh, cost, cold hours and peak power with temperature-dependent COP and recovery limits.
Compare LPG and induction cooking for the same useful heat. Estimate cylinder life, monthly fuel costs and the extra electricity bill across tariff slabs.
Estimate how long a house stays warm without power, cold-house heating time, and heat-pump night-setback savings with a two-node air and building-mass model.
Size a purifier and estimate indoor PM2.5 with outdoor leakage, deposition and indoor sources. See the steady level, cleaning time and animated particle balance.
Calculate stair rise, going, pitch, stringer layout length and headroom from total rise and run. Compare riser counts with explicit IRC or DIN dimensional checks.
Calculate a layered wall’s U-value, insulation thickness and condensation risk. See temperature, dew-point and Glaser vapour-pressure profiles through the wall.
Estimate heat-pump electricity from climate and flow temperature or a supplied JAZ. Compare gas, oil and kerosene costs with dated German tariffs and carbon-price scenarios.
Estimate room-by-room heat loss or use gas bills and degree days. Compare heat-pump capacity, bivalence and water flow with explicit assumptions.
Please confirm you want to block this member.
You will no longer be able to:
Please allow a few minutes for this process to complete.