Motor, Propeller and Battery Matcher for Drones and RC Planes
Match motor KV, propeller and battery by solving torque balance. Compare static and flight thrust, current, efficiency, winding temperature, hover throttle and capacity-based endurance.
Caution
Capacity endurance does not include wind, manoeuvres or a return-to-home reserve. Verify endurance in controlled tests and land with a measured battery reserve.
This motor propeller calculator helps RC builders, engineering students and small-aircraft designers compare a motor, propeller, ESC and battery as one electrical and aerodynamic system. Use it when choosing motor KV, changing cell count, checking current draw, or comparing hover endurance. It offers an open, inspectable eCalc alternative for the model described below.
Start with the motor maker’s KV, equivalent DC winding resistance and no-load current at its test voltage. Enter current and input-power limits for the intended run duration, then add ESC resistance. Set the battery’s series cell count, capacity, measured internal resistance and representative open-circuit cell voltage. All motors draw from the same pack, so adding motors changes voltage sag as well as total current.
Choose one of two measured UIUC propellers: APC 10 × 4.7 Slow Flyer or APC 10 × 7 Thin Electric. Their geometry is fixed to the tested propeller. For another diameter, pitch or blade count, select the custom blade-element estimate and enter the chord and airfoil-polar assumptions. Use measured coefficients whenever available: a diameter and pitch marking alone cannot determine a propeller’s real performance.
Set PWM throttle duty and axial airspeed to compare the static and forward-flight operating points. The solver finds the speed where motor torque equals propeller torque. Motor current and battery current differ at partial duty; the outputs distinguish both. Electrical input, shaft power, motor efficiency and useful propulsive efficiency help explain where energy goes. Static useful propulsive efficiency is zero because thrust does no forward work; thrust per electrical watt is the more useful static comparison.
For a drone thrust calculator, enter the number of identical rotors and the all-up mass, including the battery and payload. The hover solver finds the duty needed for each rotor to carry its share of the weight. Its capacity endurance divides usable ampere-hours by total battery current at that point. Endurance is unavailable for any operating point already below the loaded cell-voltage cutoff. A fixed-wing aircraft’s flight-duty endurance uses the selected airspeed and throttle; this tool does not calculate aircraft drag or establish that the aircraft can sustain level flight.
The animated side view shows the pitched blades, motor envelope and an ideal actuator-disk slipstream coloured by axial velocity. The torque chart marks the operating point. Coefficient and throttle curves show how the match changes away from that point.
Use this KV propeller battery calculator for comparison before a thrust-stand test. The temperature result is a single-node heating estimate with user-specified cooling, not a hotspot prediction. Battery voltage and resistance remain fixed during the endurance arithmetic. Wind, manoeuvres, descent, rotor interference, ESC switching losses, propeller flexibility and a discharge-voltage curve are outside the model. Update mass and resistance when comparing larger batteries, check the actual maker’s ratings, and measure current and temperature on the assembled system.
How it is calculated
The electrical model follows Drela, First-Order DC Electric Motor Model (2007), pp. 1–3. With KV converted to turns per second per volt, . The no-load reference speed is in rpm; the requested speed-dependent extension uses . Thus and .
For ideal PWM duty , , , and . Substitution gives the explicit current function used inside Brent's fzero torque balance. Propeller loading is , , and , with in revolutions per second. A second bracketed root solves for hover.
The UIUC presets use PCHIP interpolation of the attached static RPM tables and the two approximately 6500 rpm wind-tunnel runs per propeller. The low-J run is used below the high-J run's first sample, then the high-J run is used. An interpolated static anchor closes J=0. Each wind-tunnel curve is multiplied by the ratio of the static coefficient at operating RPM to its static anchor. This Reynolds correction assumes the advance-curve shape stays fixed.
Custom mode integrates blade lift and drag in 64 radial midpoint cells. A constant geometric pitch sets twist; chord tapers as . The assumed polar is , , with Prandtl tip loss. A bracketed root matches integrated thrust to uniform-inflow momentum theory at each of 81 advance ratios. PCHIP then supplies coefficients to the same motor solver. These custom geometry/polar equations are derived estimates, not a fit to either measured preset.
Power is accounted from battery chemical input through pack, ESC, copper and rotational losses to the shaft. Motor efficiency uses motor-terminal input; overall flight efficiency is . Capacity endurance is minutes. A constant-loss single thermal node gives .
The picture uses , , . Its illustrative axial transition is and stream-tube radius follows continuity. This is an ideal disk illustration, not a resolved wake simulation.
Assumptions
Identical direct-drive motors, one ESC per motor, a shared series battery pack, equal loading and ideal PWM with continuous motor current. No regenerative or windmilling branch. Hover has separated disks outside ground effect and still air; forward-flight speed is axial to the propeller, not the tilted-rotor freestream of a moving multirotor.
Resistance is an effective DC value at the condition being compared and is held fixed. Speed-scaled no-load current represents combined rotational loss. Cooling resistance and effective heat capacity are user assumptions; defaults of 5 K/W and 450 J/(kg·K) are illustrative, not measured SunnySky thermal parameters. The 27.5 × 30 mm motor envelope comes from the X2212 data sheet. Custom mode assumes uniform axial induction and a smooth lift plateau; it omits swirl and a measured stall/Reynolds polar.
Where it applies
Use the measured presets only for the named two-blade propellers. SF static data span 2377–6528 rpm; E data span 1975–6542 rpm. Outside these ranges the endpoint coefficients are held, with a warning at the selected operating point; full-duty capability and hover may also depend on this extrapolation. The first interval between static and wind-tunnel data is interpolated. Only positive thrust is supported; increase duty or reduce speed if the powered solution leaves that map.
The custom blade-element model is a screening estimate for pitch/diameter 0.15–1.5 and chord/diameter up to 0.2. Its 64-cell radial integration and 81-point advance map are exposed for refinement; plotted coefficient curves interpolate between solved points. Measured low-Reynolds data can change with RPM, airfoil, surface finish and flex. Tip Mach above 0.65 is flagged; compressibility, aeroelasticity and propeller structural/RPM limits are not modeled.
The winding estimate treats all motor losses as heat in one node and does not feed heating back into resistance or resolve hotspots. The default 26 A motor rating is specified for 30 s, not indefinite operation. Replace limits for the actual duty cycle. Full-duty thrust-to-weight is an unconstrained mathematical capability, not a rating-approved value.
Endurance assumes constant voltage, resistance, load and usable capacity. It does not integrate battery state of charge or predict when voltage cutoff will occur; endurance is withheld for each operating point already below cutoff, with a message identifying the affected result. No aircraft drag, stability, manoeuvre reserve or flight-path calculation is included. Fractions used for efficiency lie between zero and one; 0.8 means 80%.
SunnySky reference cases validate only independent thrust/RPM relationships. Per-row PWM duty and whether the reported current is measured on the motor or battery side are not documented. The 100% throttle heading refers to the temperature column. This sheet therefore does not independently validate current predictions. Use a test with documented duty and supply current, or independently measured motor-side current and torque; the power column is not used in these reference cases.
At low axial airspeed, the picture shows a shorter upstream portion of the stream tube so its complete outline and velocity field fit the fixed geometric scale.
Animation slows rotor rotation to 1% and air-particle travel to 2.5% of physical speed to make both visible. Motor envelope and blade dimensions share one geometric scale; the thrust arrow varies linearly with thrust on a force scale set by the unconstrained full-duty static thrust for the selected match. Drag the thrust-arrow tip to change throttle duty.
References
- Drela, M. (2007). First-Order DC Electric Motor Model. MIT Aero & Astro, pp. 1–3. https://web.mit.edu/drela/Public/web/qprop/motor1_theory.pdf
- Brandt, J. B. and Selig, M. S. (2011). Propeller Performance Data at Low Reynolds Numbers. AIAA 2011-1255. DOI: 10.2514/6.2011-1255. Open paper: https://m-selig.web.engr.illinois.edu/pubs/BrandtSelig-2011-AIAA-2011-1255-LRN-Propellers.pdf
- UIUC Propeller Database, Volume 1, corrected online data, accessed 8 November 2026. APC SF 10x4.7: static kt0835, wind-tunnel rd0841_6512 and rd0842_6513; APC E 10x7: static pg0811, pg0817_6531 and pg0818_6519; corresponding geometry files. https://m-selig.web.engr.illinois.edu/props/volume-1/propDB-volume-1.html
- SunnySky. X2212 KV980 manufacturer specifications and measured propeller table, p. 1. https://sunnyskyusa.com/products/sunnsky-x2212 ; manufacturer PDF mirror: https://img.banggood.com/file/products/20181108031551X2212KV980.pdf
Inputs
| Input | Symbol | Unit | Default |
|---|---|---|---|
| Propeller model | prop_kind | UIUC APC 10 × 4.7 SF, 2 blades | |
| Diameter | diameter | m | 0.254 |
| Pitch per revolution | pitch | m | 0.11938 |
| Blade count | blades | 2 | |
| Motor KV Enter the usual rpm per volt value from the motor data sheet. | kv | 1/(min*V) | 980 |
| Winding resistance Use the equivalent DC resistance, not an unconverted per-phase value. | Rm | ohm | 0.092 |
| No-load current | I0 | A | 0.6 |
| No-load test voltage | Vtest | V | 10 |
| Motor mass | motor_mass | kg | 0.057 |
| Motor current limit Enter the maker’s limit for the intended run duration; the default is a 30 s rating. | Ilimit | A | 26 |
| Motor input-power limit | Plimit | W | 385 |
| ESC equivalent resistance | Resc | ohm | 0.012 |
| ESC current limit | Iesc_limit | A | 30 |
| Series cell count | cells | 3 | |
| Open-circuit cell voltage Use the voltage at the state of charge being compared. | Vcell | V | 3.8 |
| Pack capacity | capacity | mA*h | 2200 |
| Internal resistance per cell Use measured loaded DC resistance at the battery’s temperature. | Rcell | ohm | 0.006 |
| Usable capacity fraction | usable | 0.8 | |
| Battery continuous C rating | C_limit | 1/h | 25 |
| Loaded cutoff per cell | Vcut | V | 3.3 |
| Auxiliary battery current | Iaux | A | 0.25 |
| Number of motors | motors | 4 | |
| All-up aircraft mass Includes battery, motors, propellers and payload. | mass_total | kg | 1.4 |
| Throttle duty fraction Ideal PWM duty; transmitter percentage may use a different mapping. | duty | 0.65 | |
| Axial flight speed | Vflight | m/s | 8 |
| Ambient air temperature | Tair | °C | 20 |
| Ambient pressure | pair | Pa | 101325 |
| Motor-to-air thermal resistance Fit to a cooling test; this has a large effect on winding temperature. | Rthermal | K/W | 5 |
| Effective motor heat capacity | cp_motor | J/(kg*K) | 450 |
| Run duration | run_time | s | 30 |
| Winding temperature limit | Tlimit | °C | 100 |
| Chord at 75% radius | chord75 | m | 0.025 |
| Hub-to-tip radius ratio | hub_ratio | 0.18 | |
| Zero-lift angle | alpha0 | deg | -2 |
| Lift coefficient plateau | cl_max | 1.2 | |
| Profile drag coefficient | cd_zero | 0.025 | |
| Quadratic polar coefficient | cd_quad | 0.02 | |
| Radial integration cells | radial_cells | 64 | |
| Advance-ratio samples | map_points | 81 | |
| Animation time | t | s | 0.13 |
Results
With the default inputs above, the calc gives:
| Result | Value |
|---|---|
| Static thrust per motor | 6.084 N |
| Flight thrust per motor | 4.049 N |
| Static speed | 5,860 1/min |
| Flight speed | 5,998 1/min |
| Static motor current | 10.62 A |
| Flight motor current | 9.57 A |
| Static battery current | 27.87 A |
| Flight battery current | 25.14 A |
| Static motor electrical input | 73.9 W |
| Flight motor electrical input | 67 W |
| Static shaft power | 61.4 W |
| Flight shaft power | 56.3 W |
| Static motor efficiency | 0.83 |
| Flight motor efficiency | 0.84 |
| Static battery-to-shaft efficiency | 0.773 |
| Overall propulsive efficiency | 0.452 |
| Static winding temperature | 33.1 °C |
| Flight winding temperature | 31.2 °C |
| Static thrust per battery watt | 7.81 g/W |
| Static duty capacity endurance | 3.79 min |
| Flight duty capacity endurance | 4.2 min |
| Hover throttle duty fraction | 0.47 |
| Hover battery current | 11.57 A |
| Hover capacity endurance | 9.13 min |
| Unconstrained full-duty thrust-to-weight | 3.24 |
| Static loaded battery voltage | 10.9 V |
| Flight loaded battery voltage | 10.95 V |
| Hover thrust match | Hover thrust attainable |
| Selected-duty limits | Selected-duty limits met |
Checked against sources
Each case below was calculated by this calc and agrees with the value from its source (within the tolerance where one is shown).
SunnySky APC 1047: 1100 gf thrust/RPM
Source: SunnySky X2212 KV980 manufacturer data sheet, p. 1: APC1047 at 11.1 V, 1100 gf and 7748 rpm. Invert the measured thrust using a 1.1 kg equivalent load and one rotor, and compare required RPM with an absolute tolerance of 200 rpm (2.6%). This independently checks the propeller thrust/RPM relation using the UIUC coefficients. Per-row PWM duty and current measurement location are not specified, so neither motor current nor supply current is an expected reference value. The 100% throttle heading applies to the temperature column.
Inputs: Number of motors = 1; All-up aircraft mass = 1.1 kg; Open-circuit cell voltage = 3.7 V; Internal resistance per cell = 0 Ω; ESC equivalent resistance = 0 Ω; Auxiliary battery current = 0 A; the others as above.
| Result | Source | This calc |
|---|---|---|
| Required hover speed | 7,748 ± 200 rpm | 7,722 rpm |
SunnySky APC 1047: 1650 gf thrust/RPM
Source: SunnySky X2212 KV980 manufacturer data sheet, p. 1: APC1047 at 14.8 V, 1650 gf and 9409 rpm. Invert the measured thrust using a 1.65 kg equivalent load and one rotor, and compare required RPM with an absolute tolerance of 300 rpm (3.2%). Coefficients above 6528 rpm are held at the UIUC endpoint, rather than fitted to this measurement. The sheet does not document per-row PWM duty or current measurement location; its current values are not used as independent validation of either current output.
Inputs: Number of motors = 1; All-up aircraft mass = 1.65 kg; Series cell count = 4; Open-circuit cell voltage = 3.7 V; Internal resistance per cell = 0 Ω; ESC equivalent resistance = 0 Ω; Auxiliary battery current = 0 A; the others as above.
| Result | Source | This calc |
|---|---|---|
| Required hover speed | 9,409 ± 300 rpm | 9,457 rpm |
Related Resources
Related articles
-
Trapezoidal Control of a Brushless DC (BLDC) Motor Using PLECS RT Box with LaunchPad–Nucleo Interface for Real-Time Hardware-in-the-Loop Validation -
Fault Detection for Electric Motors Using Vibration Analysis with 4 kHz PWM Excitation -
Modeling Lithium-Ion Battery Chargers with only Resistor and RC packed using PLECS

Responses