Moment of Inertia, Centroid & Section Modulus Calculator

Calculate area, centroid, principal moments, elastic and plastic section moduli for standard shapes, built-up sections and polygons. See biaxial bending stress on the profile.

#biaxial-bending #Green's theorem #numerical stability #plastic-section-modulus #principal-axes #section-properties #thin-walled-torsion #translation-invariance

A cross-section’s shape controls how a beam bends. This moment of inertia calculator finds the area, centroid and second moments of area of rectangles, hollow rectangles, circles, tubes, I sections, T sections, channels, angles and Z sections. It also accepts built-up sections and custom polygons. Engineers can transfer the calculated inertia into a beam deflection calculation; students can inspect the signed-area and parallel-axis steps.

Choose a profile and enter its dimensions. The default is an IPE 200 geometry, including 12 mm root fillets. Width and height describe the outside envelope; for a Z section, width means the full distance between the two outer flange tips. T, channel, angle and Z outlines have square corners. The centroid coordinates are measured from the bottom-left envelope corner of a named profile. Circular profiles use an origin at the bottom-left corner of the enclosing square.

For a built-up section, specify up to six rectangles or circles. Each part is positioned by its centroid, and rectangles may be rotated. Add material or subtract a hole. Split overlapping solids into non-overlapping pieces: the calculator rejects double-counted material. Each hole must lie strictly within one solid part. All parts represent one homogeneous section acting together.

For a custom polygon, set its vertex count and open the coordinate table’s Own values form. Enter consecutive x and y pairs, using either clockwise or counterclockwise order. Do not repeat the first point. Up to forty vertices are supported, with vertices 21–40 in the second table. Unused coordinates remain zero. A crossing, repeated point or self-touch is rejected. This makes the centroid calculator useful for irregular plates as well as familiar textbook sections.

The steel-coloured view locates the centroid C and principal axes 1 and 2. The adjacent colour field shows longitudinal bending stress under the entered Mx and My, with its elastic neutral axis marked N.A. Positive stress means tension. Drag the height or diameter handle to reshape a standard profile; set the drawing span large enough first so its scale stays fixed during the drag.

The section modulus calculator reports elastic values on both sides of each coordinate axis, plastic moduli, plastic neutral axes and radii of gyration. For an unsymmetric section, use the coupled stress calculation: a geometric Ix/c value alone does not give stress under a pure Mx. Principal-direction plastic values describe the corresponding yielded stress blocks, rather than a complete biaxial yield surface.

Thin-walled open-section torsion is estimated separately from polar inertia. For custom or built-up profiles, supply a matching open-wall strip table if that estimate is needed. Closed cells cannot use that strip sum. This tool does not check local or lateral buckling, shear centre, warping restraint, welds, yielding capacity, fatigue, residual stresses or connection strength.

How it is calculated

Boundary integration implements Green’s theorem in coordinates shifted near the section. For each local edge, ci=xiyi+1−xi+1yic_i=x_i y_{i+1}-x_{i+1}y_i. Signed sums give area and first moments; holes contribute negatively. A first pass finds the centroid relative to the nearby origin. A second pass integrates moments directly about that centroid, avoiding subtraction of nearly equal global moments. The absolute centroid is restored afterward, and origin moments follow the forward parallel-axis theorem, for example Ix0=Ix+Ayˉ2I_{x0}=I_x+A\bar y^2. These equations are derived here; Soerjadi’s polygon-moment paper provides independent background.

The inertia tensor is diagonalized to obtain I1≥I2I_1\ge I_2 and the major-axis angle. Elastic geometric section moduli are I/cI/c at each extreme fibre; radii of gyration are I/A\sqrt{I/A}. For every plastic-axis direction, a half-plane clip computes area and first moment; bisection locates the line dividing material area equally. Bisection and the integration of absolute distance from that line stay in local coordinates. Only the reported plastic neutral-axis position is translated back. Extreme-fibre distances and the bending stress field also use centroidal coordinates.

Biaxial stress is σ=a(x−xˉ)+b(y−yˉ)\sigma=a(x-\bar x)+b(y-\bar y) with a=(−MyIx−MxIxy)/(IxIy−Ixy2)a=(-M_y I_x-M_x I_{xy})/(I_xI_y-I_{xy}^2) and b=(MxIy+MyIxy)/(IxIy−Ixy2)b=(M_x I_y+M_y I_{xy})/(I_xI_y-I_{xy}^2). Resultant checks enforce Mx=∫yσ dAM_x=\int y\sigma\,dA and My=−∫xσ dAM_y=-\int x\sigma\,dA.

Open-section torsion uses J≃∑Liti3/3J\simeq\sum L_i t_i^3/3. Circular torsion is analytical; a solid rectangle uses the Saint-Venant odd-harmonic series through harmonic 79. A thin rectangular tube uses J≃4Am2/∮ds/tJ\simeq4A_m^2/\oint ds/t.

Assumptions

One homogeneous material; all built-up pieces act together without slip. Plastic section moduli assume equal tensile and compressive yield stress and ideal perfectly plastic material. The stress picture uses linear-elastic plane-section bending, without axial force.

xx points right and yy upward. IxyI_{xy} means the positive integral of the coordinate product, rather than its negative tensor entry. Principal angle is measured counterclockwise from +x to axis 1; it is set to zero when the section is isotropic, where every direction is principal. Named-shape origins are at the bottom-left envelope corner; built-up and polygon coordinates use the entered origin.

RHS corners are square. Only the I section has specified circular root fillets. Other named open sections are ideal flat-sided profiles, not complete rolled-product catalogues.

Where it applies

Polygon integrals and half-plane clips are exact for the represented straight edges. Local coordinate frames prevent large global offsets from corrupting centroidal properties. Features must still be distinguishable in the entered double-precision coordinates; shifting cannot recover detail already lost when those coordinates were rounded. Circular boundaries and I-section fillets are inscribed polygons: 96 segments per quarter circle by default. A full circle’s area error is about 0.0045%, its second-moment error about 0.009%; increase the arc resolution for tighter accuracy. Default plastic bisection uses 36 iterations. The stress field is linear, sampled on 48 × 40 points and smoothly interpolated, with clipping to the represented boundary. Geometry, rather than the display grid, controls calculated properties.

Elastic Ix/c and Iy/c are geometric moduli: for Ixy ≠ 0 they do not independently predict stresses under pure coordinate-axis moments. Plastic moduli about a chosen direction are yielded stress-block moments; an unsymmetric block can produce a coupled moment about the other axis. No full plastic interaction surface or ductility check is provided.

Open-wall torsion omits fillet/junction corrections, warping and end restraints. For example, the default IPE geometry gives about 5.17 cm⁴ by the strip sum, while the Orange Book lists 6.92 cm⁴ for the rolled profile; use it for slender, genuinely open walls, not a closed loop assembled from strips. The polar area moment is generally not the Saint-Venant torsion constant. A missing custom open-wall model leaves J blank. Thin closed-wall RHS torsion also requires slender walls. No torsion solution is inferred from an arbitrary polygon.

Six built-up parts and forty polygon vertices are interface limits. Added parts may touch but cannot overlap; each disjoint hole must be strictly inside one added part. The tool does not perform Boolean unions or stiffness transformations for different materials. Degenerate and self-intersecting polygons are invalid.

Published rolled-profile properties can differ from nominal idealized outlines. The Nucor W8×31 reference retains its listed 0.51 in fillet radius and records the resulting approximately 1% discrepancy in area, strong-axis inertia and plastic modulus; no formula or radius is fitted to erase it. Use the supplier’s certified section data for procurement and final design.

References

  • Young, Budynas & Sadegh, Roark’s Formulas for Stress and Strain, 8th ed., 2012; textbook context for section properties and torsion. Publisher: https://www.mheducation.com/highered/mhp/product/roark-s-formulas-stress-strain-8th-edition.html
  • Pilkey, Formulas for Stress, Strain, and Structural Matrices, 2nd ed., 2005. DOI: https://doi.org/10.1002/9780470172681 . Textbook reference; no paywalled tables reproduced.
  • Soerjadi, On the Computation of the Moments of a Polygon, with Some Applications. TU Delft repository: https://repository.tudelft.nl/file/File_13392aec-e14d-4f3d-b3d8-8691e89ed7b7
  • ArcelorMittal Orange Book, IPE section properties, IPE 200: https://orangebook.arcelormittal.com/node/232
  • ArcelorMittal Orange Book, HE section properties, HE 200 A: https://orangebook.arcelormittal.com/node/16
  • Nucor-Yamato Steel, Structural Shapes, March 2024 W-section table, PDF p. 37: https://nucoryamato.com/StaticData/catalog.pdf
  • Baker & Haynes, Engineering Statics, Example 10.4.2 (T Shape): https://engineeringstatics.org/Chapter_10-moment-of-inertia-of-composite-shapes.html
  • Australian Steel Institute, Flexural-torsional (Lateral) Buckling in Cold-formed Sections, 4th ed., Eq. 5.10, open-wall J: https://www.steel.org.au/getattachment/28ddf36c-cd4d-44c0-8d01-15b5bf7c0330/Flexural-torsional-%28-Lateral%29-buckling-in-Cold-Formed-sections_bk150.pdf

Inputs

InputSymbolUnitDefault
ProfileshapeI section
Overall widthbmm100
Overall heighthmm200
Web thicknesstwmm5.6
Flange thicknesstfmm8.5
Root fillet radiusr_rootmm12
Outside diameterdmm100
Wall thicknesst_wallmm5
Bending moment Mx
Positive Mx gives tension above the centroid in a symmetric section.
MxkN*m10
Bending moment My
Moments are defined by Mx = ∫yσ dA and My = −∫xσ dA.
MykN*m1.5
Segments per quarter circlen_arc96
Plastic-axis bisectionsn_bisect36
Drawing span
Keep this fixed while dragging a dimension; enlarge it to fit a larger profile.
view_spanmm320
Number of partsn_parts3
Number of vertices
Enter consecutive boundary vertices; either winding works; do not repeat the first point.
n_vertices6
Part 1 shapep1_typeRectangle
Part 1 operationp1_signAdd material
Width / diameterp1_bmm100
Heightp1_hmm10
Centroid xp1_xmm50
Centroid yp1_ymm5
Rotationp1_adeg0
Part 2 shapep2_typeRectangle
Part 2 operationp2_signAdd material
Width / diameterp2_bmm10
Heightp2_hmm180
Centroid xp2_xmm50
Centroid yp2_ymm100
Rotationp2_adeg0
Part 3 shapep3_typeRectangle
Part 3 operationp3_signAdd material
Width / diameterp3_bmm100
Heightp3_hmm10
Centroid xp3_xmm50
Centroid yp3_ymm195
Rotationp3_adeg0
Part 4 shapep4_typeRectangle
Part 4 operationp4_signAdd material
Width / diameterp4_bmm20
Heightp4_hmm20
Centroid xp4_xmm80
Centroid yp4_ymm100
Rotationp4_adeg0
Part 5 shapep5_typeRectangle
Part 5 operationp5_signAdd material
Width / diameterp5_bmm20
Heightp5_hmm20
Centroid xp5_xmm100
Centroid yp5_ymm100
Rotationp5_adeg0
Part 6 shapep6_typeRectangle
Part 6 operationp6_signAdd material
Width / diameterp6_bmm20
Heightp6_hmm20
Centroid xp6_xmm120
Centroid yp6_ymm100
Rotationp6_adeg0
Vertex table 1–20
Choose Own values and enter consecutive coordinate pairs; unused pairs can stay zero.
poly1L polygon
Vertex table 21–40
Choose Own values and enter consecutive coordinate pairs; unused pairs can stay zero.
poly2Additional vertices
Open-wall strip table
Supply centreline strips only for an open thin-walled section; closed cells need a different torsion solution.
open_wallsNot specified

Results

With the default inputs above, the calc gives:

ResultValue
Cross-sectional area2,848.4308 mm²
Centroid x50 mm
Centroid y100 mm
Centroidal second moment Ix19,431,836.0647 mm⁴
Centroidal second moment Iy1,423,684.5832 mm⁴
Centroidal product ∫xy dA0 mm⁴
Major principal second moment19,431,836.0647 mm⁴
Minor principal second moment1,423,684.5832 mm⁴
Major principal axis from +x0 deg
Radius of gyration about x82.5951 mm
Radius of gyration about y22.3565 mm
Major principal radius of gyration82.5951 mm
Minor principal radius of gyration22.3565 mm
Elastic modulus x · top194,318.3606 mm³
Elastic modulus x · bottom194,318.3606 mm³
Elastic modulus y · right28,473.6917 mm³
Elastic modulus y · left28,473.6917 mm³
Minimum elastic modulus · principal 1194,318.3606 mm³
Minimum elastic modulus · principal 228,473.6917 mm³
Plastic section modulus x220,640.4063 mm³
Plastic section modulus y44,612.3023 mm³
Plastic modulus · principal 1220,640.4063 mm³
Plastic modulus · principal 244,612.3023 mm³
Plastic neutral-axis height100 mm
Plastic neutral-axis x50 mm
Shape factor about x1.1355
Shape factor about y1.5668
Polar second moment (not torsion J)20,855,520.6479 mm⁴
Saint-Venant torsion constant · stated method51,654.2427 mm⁴
Torsion methodThin-wall open-section estimate
Maximum tensile bending stress104.1421 MPa
Minimum compressive bending stress-104.1421 MPa
Elastic neutral-axis angle from +x63.9674 deg

Checked against sources

Each case below was calculated by this calc and agrees with the value from its source (within the tolerance where one is shown).

IPE 200 · rolled fillets

Source: ArcelorMittal Orange Book, IPE 200 row: A 28.5 cm²; strong/weak I 1940/142 cm⁴; Wel,strong 194 cm³; Wpl 221/44.6 cm³. Manufacturer axis y maps to this calculator x. Published values are rounded.

Inputs: the default inputs above.

ResultSourceThis calc
Cross-sectional area2,850 ± 2.85 mm²2,848 mm²
Centroidal second moment Ix19,400,000 ± 58,200 mm⁴19,431,836 mm⁴
Centroidal second moment Iy1,420,000 ± 7,100 mm⁴1,423,685 mm⁴
Elastic modulus x · top194,000 ± 582 mm³194,318 mm³
Plastic section modulus x221,000 ± 663 mm³220,640 mm³
Plastic section modulus y44,600 ± 133.8 mm³44,612 mm³

HE 200 A · wide flange

Source: ArcelorMittal Orange Book, HE 200 A row: A 53.8 cm²; I 3690/1340 cm⁴; plastic moduli 430/204 cm³. Circular root fillets retained; tolerances allow published rounding.

Inputs: Overall width = 200 mm; Overall height = 190 mm; Web thickness = 6.5 mm; Flange thickness = 10 mm; Root fillet radius = 18 mm; the others as above.

ResultSourceThis calc
Cross-sectional area5,380 mm²5,383 mm²
Centroidal second moment Ix36,900,000 ± 73,800 mm⁴36,921,833 mm⁴
Centroidal second moment Iy13,400,000 ± 53,600 mm⁴13,355,100 mm⁴
Plastic section modulus x430,000 ± 1,290 mm³429,488 mm³
Plastic section modulus y204,000 ± 612 mm³203,818 mm³

Worked T · reference axes

Source: Engineering Statics, Example 10.4.2, T Shape: 90×20 mm flange, 30×60 mm stem. Published Ix = 11.04×10⁶ and Iy = 8.64×10⁶ mm⁴ are about bottom and left reference axes, not centroidal axes.

Inputs: Profile = T section; Overall width = 90 mm; Overall height = 80 mm; Web thickness = 30 mm; Flange thickness = 20 mm; the others as above.

ResultSourceThis calc
Second moment about y = 011,040,000 mm⁴11,040,000 mm⁴
Second moment about x = 08,640,000 mm⁴8,640,000 mm⁴

W8×31 · nominal dimensional comparison

Source: Nucor-Yamato Structural Shapes, March 2024, PDF p. 37, W8×31 row. Dimensions 8.00×7.995 in, tw .285 in, tf .435 in, R .51 in; A 9.13 in², Ix 110 in⁴, Iy 37.1 in⁴, Zx 30.4 in³, Zy 14.1 in³. Those nominal properties and the listed radius do not define exactly the same idealized outline: retaining R=.51 gives about 0.9% more area, 0.8% more Ix and 1.0% more Zx. The 1.2% comparison tolerance records this discrepancy; geometry is not retuned.

Inputs: Overall width = 203.1 mm; Overall height = 203.2 mm; Web thickness = 7.239 mm; Flange thickness = 11.049 mm; Root fillet radius = 12.954 mm; Drawing span = 430 mm; the others as above.

ResultSourceThis calc
Cross-sectional area5,890 ± 70.684 mm²5,943 mm²
Centroidal second moment Ix45,785,457 ± 549,425 mm⁴46,158,612 mm⁴
Centroidal second moment Iy15,442,186 ± 77,211 mm⁴15,434,246 mm⁴
Plastic section modulus x498,167 ± 5,978 mm³503,124 mm³
Plastic section modulus y231,058 ± 1,155 mm³231,134 mm³

Green polygon · worked T

Source: Engineering Statics Example 10.4.2, the same 90×20 mm flange and 30×60 mm stem, entered as an eight-vertex nonconvex polygon. Published origin moments 11.04×10⁶ and 8.64×10⁶ mm⁴.

Inputs: Profile = Custom polygon; Number of vertices = 8; Vertex table 1–20 = own values; the others as above.

ResultSourceThis calc
Second moment about y = 011,040,000 mm⁴11,040,000 mm⁴
Second moment about x = 08,640,000 mm⁴8,640,000 mm⁴

Built-up parallel-axis · worked T

Source: Engineering Statics Example 10.4.2; independently published T-section origin moments reproduced by two touching rectangular components using the signed-area/parallel-axis calculation.

Inputs: Profile = Built-up section; Number of parts = 2; Width / diameter = 90 mm; Height = 20 mm; Centroid x = 45 mm; Centroid y = 70 mm; Width / diameter = 30 mm; Height = 60 mm; Centroid x = 45 mm; Centroid y = 30 mm; the others as above.

ResultSourceThis calc
Second moment about y = 011,040,000 mm⁴11,040,000 mm⁴
Second moment about x = 08,640,000 mm⁴8,640,000 mm⁴

Translation regression · 10 mm square at 1 km

Source: Independent rectangle closed forms: A = bh, Ix = bh³/12, Iy = hb³/12, Zx = bh²/4, Zy = hb²/4, and σmax = |Mx|/Wx + |My|/Wy. Baker & Haynes, Engineering Statics, rectangular-area formulas; numerical translation regression with b = h = 10 mm and centre (10⁶,10⁶) mm. Global coordinate translation cannot change these properties. https://engineeringstatics.org/Chapter_10-moment-of-inertia-of-composite-shapes.html

Inputs: Profile = Custom polygon; Number of vertices = 4; Vertex table 1–20 = own values; the others as above.

ResultSourceThis calc
Cross-sectional area100 mm²100 mm²
Centroidal second moment Ix833.3 mm⁴833.3 mm⁴
Centroidal second moment Iy833.3 mm⁴833.3 mm⁴
Centroidal product ∫xy dA0 mm⁴0 mm⁴
Major principal second moment833.3 mm⁴833.3 mm⁴
Minor principal second moment833.3 mm⁴833.3 mm⁴
Plastic section modulus x250 mm³250 mm³
Plastic section modulus y250 mm³250 mm³
Plastic modulus · principal 1250 mm³250 mm³
Plastic modulus · principal 2250 mm³250 mm³
Peak absolute bending stress69,000 MPa69,000 MPa

Translation regression · 0.1 mm square at 2 m

Source: Independent textbook rectangle and elastic-bending closed forms (Baker & Haynes, Engineering Statics, rectangular-area formulas), using b = h = 0.1 mm. This is a numerical regression at the built-up coordinate limit (2000,2000) mm, not a measurement: I = a⁴/12, Z = a³/4, W = a³/6. https://engineeringstatics.org/Chapter_10-moment-of-inertia-of-composite-shapes.html

Inputs: Profile = Built-up section; Number of parts = 1; Width / diameter = 0.1 mm; Height = 0.1 mm; Centroid x = 2,000 mm; Centroid y = 2,000 mm; the others as above.

ResultSourceThis calc
Cross-sectional area0.01 mm²0.01 mm²
Centroidal second moment Ix8.333 × 10⁻⁶ mm⁴8.333 × 10⁻⁶ mm⁴
Centroidal second moment Iy8.333 × 10⁻⁶ mm⁴8.333 × 10⁻⁶ mm⁴
Centroidal product ∫xy dA0 mm⁴0 mm⁴
Major principal second moment8.333 × 10⁻⁶ mm⁴8.333 × 10⁻⁶ mm⁴
Minor principal second moment8.333 × 10⁻⁶ mm⁴8.333 × 10⁻⁶ mm⁴
Major principal axis from +x0 deg0 deg
Plastic section modulus x2.5 × 10⁻⁴ mm³2.5 × 10⁻⁴ mm³
Plastic section modulus y2.5 × 10⁻⁴ mm³2.5 × 10⁻⁴ mm³
Plastic modulus · principal 12.5 × 10⁻⁴ mm³2.5 × 10⁻⁴ mm³
Plastic modulus · principal 22.5 × 10⁻⁴ mm³2.5 × 10⁻⁴ mm³
Peak absolute bending stress6.9 × 10¹⁰ MPa6.9 × 10¹⁰ MPa

Translation regression · nonconvex T at 1 km

Source: Engineering Statics Example 10.4.2, 90×20 mm flange above a 30×60 mm stem. Published origin inertias are shifted using the independently known A=3600 mm² and centroid (45,50) mm, giving centroidal Ix=2.04×10⁶ and Iy=1.35×10⁶ mm⁴. Plastic blocks independently give Zx=1800(30+10)=72000 and Zy=40500+13500=54000 mm³. The entire polygon is translated by (10⁶,10⁶) mm.

Inputs: Profile = Custom polygon; Number of vertices = 8; Vertex table 1–20 = own values; the others as above.

ResultSourceThis calc
Cross-sectional area3,600 mm²3,600 mm²
Centroid x1,000,045 mm1,000,045 mm
Centroid y1,000,050 mm1,000,050 mm
Centroidal second moment Ix2,040,000 mm⁴2,040,000 mm⁴
Centroidal second moment Iy1,350,000 mm⁴1,350,000 mm⁴
Centroidal product ∫xy dA0 ± 1 × 10⁻⁶ mm⁴0 mm⁴
Major principal second moment2,040,000 mm⁴2,040,000 mm⁴
Minor principal second moment1,350,000 mm⁴1,350,000 mm⁴
Major principal axis from +x0 deg0 deg
Plastic section modulus x72,000 mm³72,000 mm³
Plastic section modulus y54,000 mm³54,000 mm³
Plastic modulus · principal 172,000 mm³72,000 mm³
Plastic modulus · principal 254,000 mm³54,000 mm³
Plastic neutral-axis height1,000,060 mm1,000,060 mm
Plastic neutral-axis x1,000,045 mm1,000,045 mm
Peak absolute bending stress261.8 MPa261.8 MPa

Related Resources

Responses

Your email address will not be published. Required fields are marked *

L ading...