Mohr’s Circle: Stress Transformation & Yield Check

Transform plane or 3D stress, inspect principal stresses and maximum shear, and compare von Mises and Tresca yield margins with an interactive Mohr circle.

#3D stress #Mohr's circle #plane-stress #principal stresses #stress transformation #Tresca #von Mises #yield check

Use this Mohr's circle calculator to turn a known stress state into the normal and shear stresses acting on rotated faces. It is intended for mechanics of materials coursework, checking hand calculations, and reviewing local stresses reported by an engineering analysis. The rotating element connects the geometry of Mohr's circle to the arrows on the actual faces.

Enter a stress state

Choose plane stress for a thin member with negligible out-of-plane traction. Enter σx, σy and τxy using one consistent sign convention: normal tension is positive, and positive τxy acts in the +y direction on the +x face. Compression is negative. In 3D mode, enter all six independent components of the symmetric stress tensor. The calculator includes σz, τyz and τzx when finding the principal stresses and yield equivalents.

Set the element angle, drag a blue handle, or press play. In plane stress, θ is measured counterclockwise from the original x axis to a′. Point P represents the a′ face; Q represents the perpendicular b′ face. Their diameter turns through twice the element angle. The vertical axis is −τ, so a positive physical counterclockwise rotation also moves the diameter counterclockwise.

Read principal stresses and shear

The principal stress calculator orders all three tensor eigenvalues as σ₁ ≥ σ₂ ≥ σ₃. Plane stress includes a zero eigenvalue, which need not be the smallest principal stress. The separate XY results give the two extrema within the original x–y section and their angles. The maximum in-plane shear is the XY circle radius; absolute maximum shear uses the largest difference among all three principal stresses.

In 3D mode, the 3D Mohr circle view shows the three principal-pair circles. Select axes 1–3, 1–2 or 2–3 to rotate within that principal plane. Here θ starts from the first selected principal axis, rather than the original x axis. The direction table relates each principal axis to the original coordinates. It lists direction cosines; reversing all three signs describes the same axis. For a general tensor, an XY normal-stress extremum is not necessarily a full 3D principal direction.

Compare yield criteria

Enter the material's uniaxial yield strength and the required factor of safety. The von Mises stress calculator and Tresca calculation use the complete active tensor. Each factor of safety is yield strength divided by equivalent stress. The margin check tests both against your required factor; Tresca is at least as conservative as von Mises for these assumptions.

These are local, static, isotropic ductile-yield checks. They do not cover fatigue, brittle fracture, buckling, cracks, stress concentration omitted from the input, or temperature-dependent strength changes. A hydrostatic state has zero equivalent stress in these criteria; an unbounded yield factor does not establish resistance to other failure mechanisms. Repeated principal stresses leave some principal directions nonunique.

How it is calculated

The plane-stress construction follows Beer, Johnston and DeWolf, Mechanics of Materials, 4th edition, stress-transformation lecture pp. 5–7 and worked Examples 7.01/7.02 (pp. 8–10, 17–19). With C=(σx+σy)/2C=(\sigma_x+\sigma_y)/2 and D=(σx−σy)/2D=(\sigma_x-\sigma_y)/2:

σa′=C+Dcos⁡2θ+τxysin⁡2θ,σb′=C−Dcos⁡2θ−τxysin⁡2θ,\sigma_{a'}=C+D\cos2\theta+\tau_{xy}\sin2\theta,\quad \sigma_{b'}=C-D\cos2\theta-\tau_{xy}\sin2\theta,
τa′b′=−Dsin⁡2θ+τxycos⁡2θ,R=D2+τxy2.\tau_{a'b'}=-D\sin2\theta+\tau_{xy}\cos2\theta,\qquad R=\sqrt{D^2+\tau_{xy}^2}.

The larger XY normal stress acts at θp=12atan2⁡(2τxy,σx−σy)\theta_p=\tfrac12\operatorname{atan2}(2\tau_{xy},\sigma_x-\sigma_y); the other plane is 90° away. Positive maximum shear occurs at θp−45°\theta_p-45°.

The full symmetric tensor is diagonalized with a scaled symmetric eigensolver. Eigenvalues are sorted descending; normalized eigenvectors give the direction table. MIT 16.20 Concept Question 2, pp. 2–3 provides the independent 3D reference. Each principal pair gives centre (σi+σj)/2(\sigma_i+\sigma_j)/2 and radius ∣σi−σj∣/2|\sigma_i-\sigma_j|/2. In 3D, the selected pair replaces the initial a,b stresses and starts with zero shear; the same transformation equations then apply.

Following the University of Alberta's stress-based failure criteria, τabs=(σ1−σ3)/2\tau_{abs}=(\sigma_1-\sigma_3)/2, σT=σ1−σ3\sigma_T=\sigma_1-\sigma_3, and

σVM=(σ1−σ2)2+(σ2−σ3)2+(σ3−σ1)22.\sigma_{VM}=\sqrt{\frac{(\sigma_1-\sigma_2)^2+(\sigma_2-\sigma_3)^2+(\sigma_3-\sigma_1)^2}{2}}.

Factors are n=Sy/σeqn=S_y/\sigma_{eq}, with no finite yield threshold when σeq=0\sigma_{eq}=0. A margin is met when nrequiredσeq/Sy≤1n_{required}\sigma_{eq}/S_y\le1.

Assumptions

The inputs describe one local Cauchy stress tensor; symmetry assumes ordinary moment equilibrium without couple stresses. Plane stress sets σz, τyz and τzx to zero. Positive normal stress is tension; positive τij acts along +j on the +i face. The picture plots (σa′, −τa′b′) and (σb′, +τa′b′). Red normal arrows point outward in tension, blue arrows point inward in compression, and purple arrows show signed shear. Arrow lengths share a fixed stress scale for the chosen stress state. The pictured element is a differential material element, with no inferred physical size. Yield checks assume an isotropic ductile material with equal tensile and compressive yield strengths under proportional static loading.

Where it applies

Stress transformation is an algebraic change of axes, valid for any symmetric tensor within the input range; it does not calculate stresses from external loads. The smooth sweep has 721 angular samples; the circles and current values use analytic formulas, so there is no grid or time-integration approximation. In 3D, θ sweeps only the selected principal plane, not every spatial plane. XY extrema and their angles refer to the original x–y section; they are full principal stresses only when that section is uncoupled from z. The principal direction table gives a valid basis, but eigenvector signs are arbitrary and directions within a repeated-eigenvalue subspace are nonunique. If the XY circle collapses, the displayed 0° and 90° are representative angles; every XY orientation is principal. The zero out-of-plane principal stress must still be included in plane-stress yield and absolute-shear checks.

Von Mises and Tresca predict onset of local yielding, not fatigue life, brittle fracture, buckling, fracture toughness, creep, or load redistribution after yield. They ignore hydrostatic stress; “Unbounded” therefore means no limit under these particular yield criteria. Use the actual service-temperature yield strength and stresses that already include relevant local concentrations. A met yield margin is not a component-level failure assessment.

References

  • Beer, F. P., Johnston, E. R., and DeWolf, J. T. Mechanics of Materials, 4th ed. (2006), Ch. 7; J. Walt Oler lecture notes, Examples 7.01/7.02 and Sample Problem 7.2. https://yunus.hacettepe.edu.tr/~boray/7_1_stress_transformations%20%5BCompatibility%20Mode%5D.pdf
  • Radovitzky, R. MIT 16.20 Structural Mechanics (Spring 2012), Concept Questions #1 with Solutions — Stress, Question 2, pp. 2–3. https://web.mit.edu/16.20/homepage/1_Stress/Stress_files/StressConceptQuestionsWithSolutions.pdf
  • University of Alberta, Introduction to Solid Mechanics: Stress Based Failure Criteria, sections on Tresca and von Mises. https://engcourses-uofa.ca/books/introduction-to-solid-mechanics/stress/stress-based-failure-criteria/

Inputs

InputSymbolUnitDefault
Stress statestress_modePlane stress
Normal stress σx
Tension is positive; compression is negative.
sigma_xMPa80
Normal stress σysigma_yMPa-20
Shear stress τxy
Positive τxy acts in +y on the +x face; the tensor is symmetric.
tau_xyMPa30
Normal stress σzsigma_zMPa40
Shear stress τyztau_yzMPa-20
Shear stress τzxtau_zxMPa25
3D rotation plane
θ starts along the first principal axis of the selected pair.
pairPrincipal axes 1–3 (absolute shear)
Element rotation θ
Counterclockwise from x in plane stress, or from the selected principal axis in 3D.
thetadeg25
Uniaxial yield strength
Use the yield strength at the material's service temperature.
S_yMPa250
Required factor of safetyn_required1.5

Results

With the default inputs above, the calc gives:

ResultValue
Rotated normal stress σa′85.12071 MPa
Orthogonal normal stress σb′-25.12071 MPa
Signed shear τa′b′-19.01859 MPa
Principal stress σ₁88.30952 MPa
Principal stress σ₂0 MPa
Principal stress σ₃-28.30952 MPa
XY larger principal normal stress88.30952 MPa
XY smaller principal normal stress-28.30952 MPa
XY angle to larger normal stress15.48188 deg
XY angle to smaller normal stress105.48188 deg
XY angle to +maximum shear-29.51812 deg
Maximum XY in-plane shear58.30952 MPa
Absolute maximum shear58.30952 MPa
Von Mises equivalent stress105.35654 MPa
Tresca equivalent stress116.61904 MPa
Von Mises factor of safety2.37289
Tresca factor of safety2.14373
Yield margin checkBoth yield margins met
XY orientationXY principal angles defined

Checked against sources

Each case below was calculated by this calc and agrees with the value from its source (within the tolerance where one is shown).

Beer–Johnston 4th ed., Example 7.02

Source: Beer, Johnston and DeWolf, Mechanics of Materials, 4th ed. (2006), Example 7.02, lecture pp. 17–19. Published σmax=70 MPa, σmin=−30 MPa, R=50 MPa, θp=26.6°. Independent worked-example values; angle tolerance allows printed rounding.

Inputs: Normal stress σx = 50 MPa; Normal stress σy = -10 MPa; Shear stress τxy = 40 MPa; Element rotation θ = 0 deg; the others as above.

ResultSourceThis calc
XY larger principal normal stress70 MPa70 MPa
XY smaller principal normal stress-30 MPa-30 MPa
Maximum XY in-plane shear50 MPa50 MPa
XY circle centre20 MPa20 MPa
XY angle to larger normal stress26.6 ± 0.06 deg26.565 deg

MIT 16.20 full 3D tensor

Source: Raúl Radovitzky, MIT 16.20 Structural Mechanics, Spring 2012, Concept Questions #1 with Solutions — Stress, Question 2, PDF pp. 2–3. All six components and printed eigenvalues are used; tolerances allow two-decimal rounding.

Inputs: Stress state = 3D stress tensor; Normal stress σx = 200 MPa; Normal stress σy = 300 MPa; Normal stress σz = -100 MPa; Shear stress τxy = 50 MPa; Shear stress τyz = 100 MPa; Shear stress τzx = -80 MPa; the others as above.

ResultSourceThis calc
Principal stress σ₁331.6 MPa331.6 MPa
Principal stress σ₂215.1 MPa215.1 MPa
Principal stress σ₃-146.8 MPa-146.8 MPa
Trace before rotation400 MPa400 MPa

Beer–Johnston 4th ed., Sample Problem 7.2

Source: Beer, Johnston and DeWolf, Mechanics of Materials, 4th ed. (2006), Sample Problem 7.2, lecture pp. 20–22. The initial right-face shear is negative in this calculator's tensor convention. The published 41.3 MPa is a shear magnitude; the signed transformed component is −41.3 MPa. Printed normals are 48.4 and 111.6 MPa.

Inputs: Normal stress σx = 100 MPa; Normal stress σy = 60 MPa; Shear stress τxy = -48 MPa; Element rotation θ = 30 deg; the others as above.

ResultSourceThis calc
XY larger principal normal stress132 MPa132 MPa
XY smaller principal normal stress28 MPa28 MPa
Rotated normal stress σa′48.4 ± 0.06 MPa48.431 MPa
Orthogonal normal stress σb′111.6 MPa111.6 MPa
Signed shear τa′b′-41.3 ± 0.06 MPa-41.321 MPa
XY angle to larger normal stress-33.7 ± 0.06 deg-33.69 deg

MIT 16.20 equal biaxial stress at 25°

Source: MIT 16.20 Stress Concept Question 4, PDF pp. 4–5: equal 250 MPa biaxial stresses and zero shear remain unchanged when axes rotate by 25°. The PDF calls this 2D state hydrostatic; this calculator correctly retains σz=0 for the full 3D yield calculation.

Inputs: Normal stress σx = 250 MPa; Normal stress σy = 250 MPa; Shear stress τxy = 0 MPa; the others as above.

ResultSourceThis calc
Rotated normal stress σa′250 MPa250 MPa
Orthogonal normal stress σb′250 MPa250 MPa
Signed shear τa′b′0 ± 1 × 10⁻⁶ MPa0 MPa

Related Resources

Responses

Your email address will not be published. Required fields are marked *

L ading...